后退火温度对溅射沉积Pb(Zr0.52Ti0.48)O3铁电薄膜结构和性能的影响

在具有Ti缓冲层的Pt(111)底电极上,用射频溅射工艺在较低的衬底温度(370℃)和纯Ar气氛中沉积Pb(Zr0.52Ti0.48)O3(PZT)薄膜,沉积过程中基片架作15°摇摆以提高膜厚的均匀性。然后将样品在大气中进行5min快速热退火处理,退火温度550-680℃。用XRD、SEM分析薄膜的微结构,RT66A标准铁电测试系统测量样品的铁电和介电性能。结果表明,所沉积的Pt为(111)取向,仅当后退火温度高于580℃,沉积在Pt(111)上的PZT薄膜才能形成钙钛矿结构的铁电相,退火温度在580-600℃时结晶为(110)择优取向,退火温度高于600℃时结晶为(111)择优取向。PZT薄膜的极化强度随退火温度的升高而增加,但退火温度超过650℃时漏电流急剧上升,因此退火处理的温度对PZT薄膜的结构和性能有决定性的影响。     

氢对GaAs薄膜的钝化作用

报导了射频磁控溅射与沉积气氛掺氢相结合制备单层(13~20 nm厚)高质量GaAs多晶态纳米薄膜的方法,研究了氢钝化对薄膜微观结构及光学性质的影响.对GaAs薄膜进行了X射线衍射、原子力显微镜、吸收光谱、光致荧光谱的研究分析.结果表明,衬底温度500℃的掺氢薄膜和520℃的薄膜呈面心立方闪锌矿结构，薄膜的晶团尺寸较大，微观表面较为粗糙，其吸收光谱出现了吸收边蓝移和明显的激子峰，带隙光致荧光峰强明显增加，说明氢在衬底温度500℃~520℃下对薄膜有重要的钝化作用.     

Optical properties of In2O3 oxidized from InN deposited by reactive magnetron sputtering

Unintentionally doped and zinc-doped indium nitride (U-InN and InN:Zn) films were deposited on (0 0 0 1) sapphire substrates by radio-frequency reactive magnetron sputtering, and all samples were then treated by annealing to form In₂O₃ films. U-InN and InN:Zn films have similar photon absorption characteristics. The as-deposited U-InN and InN:Zn film show the absorption edge, ∼1.8-1.9 eV. After the annealing process at 500 °C for 20 min, the absorption coefficient at the visible range apparently decreases, and the absorption edge is about 3.5 eV. Two emission peaks at 3.342 eV (371 nm) and 3.238 eV (383 nm) in the 20 K photoluminescence (PL) spectrum of In₂O₃:Zn films were identified as the free-exciton (FE) or the near band-to-band (B-B) and conduction-band-to-acceptor (C-A) recombination, respectively.     

WOx/TiO2光催化剂的可见光催化活性机理探讨

采用磁控溅射技术在用浸渍提拉法制得的TiO2薄膜上，溅射氧化钨层,通过气相反应中光催化降解二甲苯的实验表明，WOx/TiO2薄膜具有可见光活性.通过UV-Vis吸收光谱、X射线光电子能谱（XPS）等方法对其可见光活性的机理进行探索.UV-Vis吸收光谱表明WOx,TiO2对可见光响应的范围有一定的扩展,吸收强度增加.XPS表明WOx/TiO2薄膜表面形成了明显的W杂质能级和Ti缺陷能级,这是WOx/TiO2在可见光范围有一吸收的主要原因,也是光催化剂具有可见光活性的必要条件之一，同时杂质能级的存在使半导体费米能级上移,载流子增加,光催化效率提高.     

Properties of ITO films prepared by reactive magnetron sputtering

Indium tin oxide (ITO) thin films were deposited by mid frequency pulsed dual magnetron sputtering using a metallic alloy target with 10 wt.% tin in an atmosphere of argon and oxygen. The aim of the work was to study the interdependence of structural, electrical and optical properties of ITO films deposited in the reactive and transition target mode, respectively. The deposition rate in the transition mode exceeds the deposition rate in the reactive mode by a factor of six, a maximum value of 100 nm·m min⁻¹ could be achieved. This corresponds to a static deposition rate of 200 nm min⁻¹. The lowest electrical resistivity of 1.1·10⁻³ Ω cm was measured at samples deposited in the high oxygen flow range in the transition mode. The samples show a good transparency in the visible range corresponding to extinction coefficients being below 10⁻². X-ray diffraction was used to characterise crystalline structure as well as film stress. ITO films prepared in the transition mode show a slightly preferred orientation in (211) direction, whereas films deposited in the reactive mode are strongly (222) oriented. Compared to undoped In₂O₃ all samples have an enlarged lattice. The lattice strain perpendicular to the surface is about 0.8% and 2.0% for films grown in the transition and the reactive mode, respectively. Deposition in the transition mode introduces a biaxial film stress in the range of −300 MPa, while stress in reactive mode samples is −1500 MPa.     

Structural and electrochemical studies of annealed LiNiVO4 thin films

We prepared stoichiometric lithium nickel vanadate amorphous thin films by using r.f. magnetron sputtering under controlled oxygen partial pressure. The amorphous films were heated at various temperatures, 300–600 °C, for 8 h. The as‐deposited and annealed thin films were characterized by Rutherford backscattering spectroscopy, nuclear reaction analysis, Auger electron spectroscopy, X‐ray diffraction, scanning electron microscopy and atomic force microscopy. The electrochemical behavior of the various films was studied by the galvanostatic method. The cells were tested in a liquid electrolyte at room temperature, with lithium metal used as the counter and reference electrode. The best electrochemical storage value was obtained with the thin film annealed at 300 °C, which showed superior capacity and small capacity loss during cycling. Copyright © 2007 John Wiley & Sons, Ltd.     

Influence of target surface degradation on the properties of r.f. magnetron‐sputtered calcium phosphate coatings

This paper reports a detailed study of how repeated r.f. magnetron sputtering from a hydroxyapatite (HA) powder target affects the nature and reproducibility of a sequential series of thin‐film coatings deposited onto Ti6Al4V substrates. An evaluation of the effective lifespan of the HA sputter targets and the reproducibility of the calcium phosphate (CaP) coatings produced from them has been made from Fourier transform infrared spectroscopy, XPS and, as appropriate, atomic force microscopy and SEM/energy dispersive x‐ray analyses. The annulus region of the target surface, from which sputtering under r.f. magnetron conditions normally occurs, showed severe surface degradation after only one deposition run, as indicated by significant PO₄^3? and OH^? depletion. This deterioration continued after each subsequent deposition cycle but to a much lesser extent than that observed in the initial sputtering period. The layers produced from all of the sputter runs contained the expected Ca²⁺ and PO₄^3? species characteristic of a CaP system but were OH^? deficient in the as‐deposited state. However, the chemical and morphological properties of the coatings did not change significantly until after the third consecutive sputter cycle. Hence, these data indicate that, even though a significant level of degradation of the HA target occurs at the outset of the sputtering procedure, the general plasma conditions employed here have a dominant influence on the coating properties until a critical degradation condition is met. As such, the compacted HA powder targets of interest can have a life‐cycle greater than single usage without detriment to the chemistry and morphology of the coatings produced from them. Copyright © 2003 John Wiley & Sons, Ltd.     

Electronic spectral and photophysical properties of some p-phenylenevinylene oligomers in solution and thin films

A comprehensive photophysical and spectroscopic study of a new class of p-phenylenevinylene oligomers (PPV-trimers) possessing different alkyl and alkyloxy sidechain substituents and different end groups (aldehyde, CC, phenylene and anthracene units) was undertaken in solution at room temperature (293 K), low temperature (77 K) and in thin films. The study comprises absorption, emission and triplet–triplet absorption spectra, together with quantitative measurements of quantum yields (fluorescence, intersystem crossing, internal conversion and singlet oxygen formation) and lifetimes. The data allow the determination of rate constants for all decay processes. From these, several conclusions could be drawn. Changing from alkyl to alkyloxy substituents does not change fluorescence and internal conversion yields but decreases the (already small) intersystem crossing yield. The introduction of anthracene at the terminal ends of the PPV-trimers leads to the lowest fluorescence yield reported in this study. Of particular importance is the fact that the fluorescence quantum yields in films are of the same order of magnitude as those in solution, which suggests the potential for use of these oligomers for light-emitting device applications. With one of the alkyloxy derivatives, a more detailed study of the early part of the fluorescence decay was made, and it was found that upon excitation a fast conformational relaxation process of the initially excited oligomer occurs, leading to a more planar conjugation segment.     

Electron microscopic phase analysis of BN-thin films

A series of BN films was deposited by means of r.f. magnetron sputtering of a h-BN target onto Si(1OO) surfaces. Hereby, the substrate bias voltage was varied. Special interest is focussed to the influence of the deposition parameters on the orientation of the growing hexagonal BN film with respect to the substrate. For structural investigation, cross section samples were prepared. In addition to HRTEM and diffraction investigations, especially electron energy loss spectroscopy (EELS) was applied successfully for phase identification. For negative bias voltages of U _B =–300 V and U _B =–350V, we found a phase system consisting of a first-grown 25 nm thick layer of hexagonal structure with the c axis parallel to the substrate surface followed by the cubic phase.Dedicated to Professor Dr. rer. nat. Dr. h.c. Hubertus Nickel on the occasion of his 65th birthday     

Deposition of complex multielemental thin films

Modern condensed-matter physics is increasingly concerned with the design, synthesis, analysis, and exploitation of chemically complex materials and structures. Complex metal oxides and strongly correlated electron systems such as YBa₂Cu₃O_7−x and La_1−xSr_xMnO₃ are paradigmatic examples. Their production in the form of high-quality thin films is of both technological and fundamental importance and has stimulated a concerted effort in the last two decades to find and optimize efficient techniques to this end. This review discusses the physics behind and the requirements for synthesizing high-quality films of such materials and examines fundamental aspects of the growth processes associated with magnetron sputtering and pulsed laser deposition, the two techniques which presently offer the best solutions in this burgeoning field.